太赫兹可调谐滤波器设计

为了实现太赫兹信号的可调谐滤波，设计了一种基于柔性材料的太赫兹可调谐滤波器。通过扭曲特氟龙（Teflon）波导形成环型谐振器，实现了160～200 GHz频段的带阻滤波功能。改变谐振腔长可实现自由频谱范围（FSR）和滤波频点的调谐，实验测试了自由频谱范围在1.9 GHz和2.8 GHz间切换以及相应的滤波特性。研究表明，谐振腔长一定时，改变弯曲半径可实现滤波阻带抑制度的调节，柔性材料太赫兹环型谐振器可用于可调谐滤波，且具有较高的自由度。     

Optimal approximation of asymmetric type fractional-order bandpass Butterworth filter using decomposition technique

In this letter, the optimal rational approximation of fractional-order bandpass Butterworth filter (FOBBF) is presented. The transfer function of the FOBBF is decomposed into a multiplication of first-order and second-order terms. As a result, the design stability conditions can be easily satisfied using only the variable boundary constraints. The proposed technique generalizes the symmetric fractional-order roll-off characteristic as only a special case of the asymmetric one. Several examples are presented to validate the modeling efficacy.     

Influence of the porous transport layer properties on the mass and charge transfer in a segmented PEM electrolyzer

A titanium Porous Transport Layer (PTL) is usually used at the anode side of PEM water electrolyzers to ensure both the gas/water transport and the electric charges transfer. In this paper, four different sintered Ti powder PTLs were characterized to determine some properties, such as the pore size distribution, the porosity, and the permeability. Their influence on the electrolysis performance was investigated by using a 30 cm² segmented cell which allowed measuring the current density distribution, while controlling temperature and pressure conditions. For a better understanding, in-situ techniques such as the Polarization Curves and the Electrochemical Impedance Spectroscopy (EIS) were used. A local characterization of mass transport limitations caused by oxygen saturation was carried out, paying special attention to the pressure influence when using a PTL with very small pores. The results showed that current density heterogeneities can be explained by microstructure changes along the PTL. The optimal geometric characteristics of the PTL depend not only on the operating conditions such as current density, pressure, and temperature but also on the catalyst layer properties. A new model for the constriction resistance between the catalyst layer and the PTL was proposed.     

基于涡动相关法的沉积物-水界面氧通量与水动力条件响应关系

沉积物-水界面是物质参与环境地球化学循环和生物耦合的"热区",水动力条件是沉积物-水界面物质交换的关键影响因素。溶解氧作为常用的水质评价指标,对调节生物化学进程有重要作用,因此本文采用涡动相关法这种非侵入式通量测量技术开展室内试验研究,探究沉积物-水界面氧通量与水动力条件的响应关系。结果表明:随着水体紊动增加(采用Batchelor尺度表征),扩散边界层厚度减小,氧通量增大。分析室内试验和相关研究中水动力条件、扩散边界层厚度及氧通量的关系,发现扩散边界层厚度与Batchelor尺度呈正相关关系,拟合结果表明可以用Batchelor尺度近似表示扩散边界层厚度;氧通量与扩散边界层厚度呈负相关关系,且当扩散边界层厚度小于0.5 mm时,扩散边界层厚度变化对氧通量影响更强烈,当厚度大于0.5 mm后,氧通量基本保持稳定。     

改进ILoG算子的故障检测方法

针对强背景噪声干扰下轮对轴承故障特征微弱、难以准确检测的问题,提出了一种自适应改进高斯拉普拉斯(improved Laplacian of Gaussian,简称ILoG)算子的微弱故障检测方法。ILoG算子滤波器具有优良的信号突变特征检测能力,将其用于轮对轴承故障信号的冲击特征检测,同时利用水循环算法(water cycle algorithm,简称WCA)的寻优特性,并行搜寻筛选最佳的ILoG算子影响参数,通过对参数优化后ILoG算子滤波后信号做进一步包络解调分析,提取出轮对轴承微弱的故障特征信息。对实际轮对轴承外圈和内圈故障信号分析的结果表明,该方法可以有效检测出轴承微弱故障特征频率,故障检测效果优于小波阈值和多尺度形态学差值滤波方法。     

Passive target detection and tracking from electromagnetic field measurements

This paper presents a novel approach to the localization of moving targets in a complex environment based on the measurement of the perturbations induced by the target presence on an independently‐generated time‐varying electromagnetic field. Field perturbations are measured via a set of sensors deployed over the domain of interest and used to detect and track a possible target by resorting to a particle Bernoulli filter (PBF). To comply with real‐time operation, the PBF works along with an artificial neural network (ANN) model of the environment trained offline via finite elements (FEs). The performance of the proposed algorithm is assessed via simulation experiments.     

An efficient method of generating vortex electromagnetic wave based on double‐layer transmissive metasurface

A broadband double‐layer transmissive metasurface (TMS) for effective generate vortex electromagnetic wave is presented in this paper. The proposed TMS consists of two types of elements. The first element is composed of a multi‐resonant dipole and four metal vias. The metal vias increase the coupling strength between the upper and lower layers to improve transmission efficiency. On the basis of the first element, the second element adds stubs to ensure sufficient phase shift. The far‐field cross polarisation is eliminated by special element arrangement. Then, a centre‐fed linear polarisation TMS is designed to generate orbital angular momentum beams with mode l = ? 1. The proposed TMS is designed, manufactured and measured to verify the proposed design. The measured results indicate that a maximum gain of 20.8 dBi and narrow divergence angle of ±5° are achieved at 18 GHz. Furthermore, mode purity is higher than 86.1% within the 17 to 19 GHz band. The proposed double‐layer TMS saved costs, reduced weight and without assembly error is a good candidate for OAM generator.     

Microwave bandpass filter by feedback interference topology

This paper proposes a signal feedback interference topology to control the characteristics of a coupled line bandpass filter. Control is carried out by varying the ratio of the transmission line parameters of the forward and the feedback couplers. The topology produces a compact filter that does not require a complicated design or fabrication. The results of the insertion and return losses show that the feedback‐controlled design has desirable features in terms of the design frequency, fractional bandwidth, stopband rejection level, roll‐off rate and insertion loss. The test results of the fabricated prototype achieved good agreement with the simulation results of the ideal transmission line design model. Several microwave, modern wireless and mobile/satellite communication systems may benefit from such a filter design due to its compactness and flexibility.     

打印层厚度对FDM薄板固有特性的影响

针对不同打印层厚度对熔融沉积成型(fused deposition modeling,简称FDM)薄板固有特性的影响规律及相应的机理进行了研究。首先,以悬臂边界条件下的FDM薄板为研究对象,创建了固有特性理论模型;其次,完成了薄板样件的制备,同时搭建了样件的动力学测试系统,实验研究了样件的固有特性参数;最后,对比分析理论与实验结果,以验证理论模型的正确性。研究结果表明,所建模型可以准确预测FDM薄板结构的固有特征参数;打印层越厚,样件的固有频率越高,但其模态振型不会随着打印层厚度的变化而变化。该研究为提高FDM产品动力学性能提供了理论基础和技术支持。     

Composite mixed matrix membranes incorporating microporous carbon molecular sieve as filler in polyethersulfone for CO2/CH4 separation

Membrane technology has been considered a key factor for sustainable growth in high-efficiency gas separation. Current mixed matrix membranes (MMMs) technology is rising, but these membranes in the dense structure are having difficulties in operating at high pressures and scale up for commercialization. The purpose of this research is to synthesize composite MMMs (CMMMs) consisting of polyethersulfone (PES), carbon molecular sieve (CMS 1–5 wt %), and Novatex 2471 nonwoven fabric (support layer). The membranes' physical, chemical, and thermal properties were evaluated by different analytical equipment. The morphology of both PES and PES-CMS composite membranes had a porous and asymmetric structure, in which CMS was uniformly distributed in the polymer matrix. The thermal properties showed that the membranes were stable up to 350 °C with a single glass transition temperature. The functional groups in the membrane were confirmed by spectral analysis. The gas performance results showed that carbon dioxide permeance increased with increased CMS concentration and methane permeance decreased due to the hindering effect of CMS under similar operating conditions. The highest selectivity achieved was 12.774 using CMMM of 5 wt % of CMS at 10 bar, which on average was 137.80%, improved selectivity compared to pure PES membrane. The support layer was able to withstand high operating pressures and showed the ability to scale up. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48476.